CONFIGURING MOCHA RDP LITE HOW TO
CONFIGURING MOCHA RDP LITE SERIES
CONFIGURING MOCHA RDP LITE DOWNLOAD

I actually talked a little about it here. There used to be a DMZ configured but I moved it to a pfSense virtual machine. Round-trip min/avg/max/std-dev = 29.029/29.436/30.402/0.562 ms Configure sub-interfacesĪs you can see above, I have few sub-interfaces configured. PING () 56 data bytesĦ4 bytes from : icmp_seq=1 ttl=56 time=10.9 msĦ4 bytes from : icmp_seq=2 ttl=56 time=10.7 msĦ4 bytes from : icmp_seq=3 ttl=56 time=10.4 msĦ4 bytes from : icmp_seq=4 ttl=56 time=11.5 msĤ packets transmitted, 4 received, 0% packet loss, time 4005ms Here’s a better way to verify that the configuration actually worked. If you do not get an IPv6 address, use the following commands to force DHCPv6 renew. run show interfacesĬodes: S - State, L - Link, u - Up, D - Down, A - Admin Down Below is my sanitized output that shows both IPv4 and IPv6 addresses. To verify that you received IPv6 addresses, issue the command found in the example below. You will also need to issue the WAN6-LOCAL rules in the firewall section below. set system offload ipv6 forwarding enable In addition to the above configurations, you may want to configure the IPv6 forwarding offload feature as well. Set interfaces ethernet eth0 dhcpv6-pd pd 0 interface eth2 service slaac Set interfaces ethernet eth0 dhcpv6-pd pd 0 interface eth2 prefix-id :5 Set interfaces ethernet eth0 dhcpv6-pd pd 0 interface eth2 host-address ::1 Set interfaces ethernet eth0 dhcpv6-pd pd 0 interface eth1.100 service slaac Set interfaces ethernet eth0 dhcpv6-pd pd 0 interface eth1.100 prefix-id :4 Set interfaces ethernet eth0 dhcpv6-pd pd 0 interface eth1.100 host-address ::1 Set interfaces ethernet eth0 dhcpv6-pd pd 0 interface eth1.99 service slaac Set interfaces ethernet eth0 dhcpv6-pd pd 0 interface eth1.99 prefix-id :3 Set interfaces ethernet eth0 dhcpv6-pd pd 0 interface eth1.99 host-address ::1 Set interfaces ethernet eth0 dhcpv6-pd pd 0 interface eth1.2 service slaac Set interfaces ethernet eth0 dhcpv6-pd pd 0 interface eth1.2 prefix-id :2 Set interfaces ethernet eth0 dhcpv6-pd pd 0 interface eth1.2 host-address ::1 Set interfaces ethernet eth0 dhcpv6-pd pd 0 interface eth1 service slaac Set interfaces ethernet eth0 dhcpv6-pd pd 0 interface eth1 prefix-id :1 Set interfaces ethernet eth0 dhcpv6-pd pd 0 interface eth1 host-address ::1 set interfaces ethernet eth0 dhcpv6-pd pd 0 prefix-length /60 In business class accounts, they can ask for /56 or 256 x /64 prefixes. In residential networks, Comcast/Xfinity allows the user to ask for a maximum of 16 x /64 prefixes or /60. Pay attention to the prefix-length that you’re asking for. There are two EdgeOS configurations I found that worked for me, but I will only show the one that I think is the best out of the two that I tried. My ISP uses prefix delegation, which provides a mechanism for automated delegation of IPv6 prefixes using DHCP.

CONFIGURING MOCHA RDP LITE HOW TO

Once I found out, I started researching on how to configure it on my router.

CONFIGURING MOCHA RDP LITE DOWNLOAD

In fact, I accidentally found that out when I was troubleshooting my slow download speed connection. I actually did not know that my ISP (Comcast/Xfinity) has been IPv6 ready for about two years now (fully deployed). As far I know (I could be wrong), IPv6 in US residential networks has only been around two to three years. I would say that IPv6 in residential networks is relatively new, at least in the US.

CONFIGURING MOCHA RDP LITE SERIES

That said, I created the Hardening EdgeRouter Lite series to address some of the security concerns. UPDATE: While there are some security related configurations covered in this series, there are still some security concerns with the configuration. Though, I did include one feature that I turned on for few days and decided to turn it off because of issues that I encountered with it being on. In this post, I will talk about features that I personally use at home at the time of writing. In part one, I covered what I think are the essential configurations to get a user going in a typical home environment setup. If you haven’t read the part one, you might want to read that first. This is part two of the How to configure EdgeRouter Lite via CLI blog post. Remote Access VPN with two-factor authentication How to configure EdgeRouter Lite via CLI – Part 1ĮdgeOS configuration guide for CLI junkies This blog post is part of a series on EdgeRouter Lite.

Configuring mocha rdp lite